New 630D Draper

Grain Harvesting
REQUEST A QUOTE
REQUEST A QUOTE
Key Features
  • Windrowing capability with 600D Drapers
  • Dual-knife drive system is timed
  • Cutterbar is closer to the ground
  • Stainless-steel feed floor

More Info

Features

Takes only one person a few minutes to convert draper from field to transport without use of tools

The 630D, 635D, and the 640D Draper models can be equipped with an integral, slow-speed transport system.

 

Customer Value:

  • Dual-front dolly wheel tires with an extendable tongue and two-gauge wheel tires carry the complete weight of the draper when in transport, eliminating the need for a header trailer
  • One person can convert the draper from field to transport mode in a few minutes without the use of tools, expediting road transport
600D integral transport system600D integral transport system
600D integral transport system pulled by tractor600D integral transport system pulled by tractor
Theory of Operation:
Step 1-lock left-hand gauge wheels in placeStep 1-lock left-hand gauge wheels in place
Step 2-lock right-hand gauge and transport wheelsStep 2-lock right-hand gauge and transport wheels
Step 3-position transport warning lightsStep 3-position transport warning lights
Step 4-install transport tongueStep 4-install transport tongue

 

In field mode, the dual wheels become the left- and right-hand gauge wheels. For transport, the left-hand dual-dolly wheels support one side of the draper frame and the right-hand dual wheels are repositioned to support the right-hand end of the frame.

 

The transport package includes warning lights, which can be plugged into a seven-way power source for road transport with a 32.2-km/h (20-mph) speed limit for farm equipment transport.

 

NOTE: The 630D, 635D, and the 640D Drapers are equipped with two 20.5 x 8.0 12-ply equivalent gauge wheel tires as base equipment and four 20.5 x 8.0 12-ply equivalent gauge wheels with the low-speed transport option.

Dual-knife drive system is timed
Cutterbar epicyclical gearcaseCutterbar epicyclical gearcase
Knife drive shaftKnife drive shaft

The unique dual-knife-drive system is timed, creating the smoothest-possible reciprocating knife-drive system currently in the industry. The positive, reliable shaft-driven dual epicyclical in-line knife drives with built-in driveline protection provide operators with the strongest knife-drive system.

Double-cut knife system produces a cleaner cut

All John Deere 600D Drapers include a double-cut knife which features a hydraulic tilt that is controlled from inside the cab. All 10.6-m (35-ft) and 12.1-m (40-ft) draper cutterbars also have knifeback reinforcement straps to strengthen the knifeback.

 

Customer Value:

  • Longer stroke of knife section provides a faster, cleaner, and smoother cut which allows operators to harvest at faster ground speeds maximizing productivity
  • Reinforced knifeback strengthens cutterbar for tough harvesting conditions maximizing performance
  • Hardened sickle sections and unique boron treatment extends wear life
  • Hydraulic tilt optimizes the cutterbar angle for varying conditions, extending the harvest day and providing the lowest-possible cut height
Double-cut cutterbar systemDouble-cut cutterbar system
Double-cut rock guardDouble-cut rock guard
Theory of Operation:

The 100-mm (4-in.) cutting action produces a cleaner cut versus the tearing effect of shorter-stroke cutting systems. Knife hold-downs are easily adjusted to help maintain harvesting performance.

Tilt cylinderTilt cylinder
#

 

The cutterbar hydraulic tilt adjusts a full 8 degrees while maintaining excellent visibility to the cutterbar throughout the tilt range. For improved ease of use the optional advanced hydro handle can be configured to control the platform tilt.

Reel resume and reverse are features on the 600D Drapers

Reel resume and reverse are features on the 600D Drapers. The combine operator can store two different reel positions with one setting for normal conditions and another for down, tangled, short, leaning crops. 

 

Customer Value:

  • Added time savings and convenience with saved reel positions, lowering operator fatigue
  • Reel-reverse feature reverses the reel in conjunction with the center feed drum and belt to back out plugs and increase harvest efficiency
Draper drumDraper drum
Draper reelDraper reel

Specifications

Compare >>>

Select up to 2 models to compare specifications

John Deere630D Draper
Add Model
Add Model
Cutterbar
Type Straight line knife drive system
Length 9.3 m
30.5 ft
Knife drive Dual knife base, single optional (for combine use only)
Knife speed 490 cycles/min
Cutterbar tilt Base hydraulic, 9 degrees tilt maximum
Pickup reel
Number of slats 6 bat poly base, 6 bat steel optional
Fingers Nylon base, steel optional
Diameter 1,067 mm
42 in.
Height control Hydraulic
Speed control Hydraulic
Reel lift Cylinder stroke 330 mm
13 in.
Total Range 391.5 mm
15.4 in.
Reel fore and aft Cylinder stroke 359 mm
14.1 in.
Total range 620 mm
24.4 in.
Reel resume Base
Reel reverse Base
Operating speeds 6-54 rpm
Operating speeds (54-in. reel)
Slat reel
Number of slats
Diameter
Height control
Speed control
Operating speeds
Draper belts
Width Side belts 1,016 mm
40 in.
Center belts 1,397 mm
55 in.
Center belt not included with SPW configuration
Clean height 25.4 mm
1 in.
Operating speed Side belts: variable up to 223 m/min
735 fpm
Center belts: 212 m/min
695 fpm
Center belt not included with SPW configuration
Speed control Hydraulic from cab
Center belt reverse Base; Center belt not included with SPW configuration
Feed drum
Diameter 406 mm
16 in.
Feed drum not included with SPW configuration
Feed drum fingers Heavy duty round 16 mm (0.625 in) diameter with breakaway notch and retainer
Number of fingers 18
Auger finger platform Dual chevron, retracting
Finger reach 195 mm
6 in.
Drum/auger reverse Base
Operating speed 195 rpm
Center clean out door Base
Header height sensing
Type Electro-hydraulic base
Header height sensing on the ground Base
Header height sensing off the ground Base
Auxiliary top auger
Type Optional hydraulic drive
Dimensions
Platform length 10.0 m
32.9 ft
Overall operating depth 2.5 m
8.2 ft
Transport width, field position 9.9 m
32.5 ft
Transport width on wheel, less dividers 2.7 m
8.9 ft
Transport length, hitch extended 12.3 m
40.4 ft
Weight
Approximate weight (slat reel)
Approximate weight (pickup reel) Combine only 3,109 kg
6,855 lb
SPW only 2,509 kg
5,532 lb
Approximate weight (with transport) Combine only 3,286 kg
7,245 lb
SPW only 2,686 kg
5,922 lb
Approximate weight (optional 54-in. reel)

Accessories and Attachments

600 Series HydraFlex Platforms

Platform wedge kit - BH84398
Wedge kitWedge kit

In certain field conditions, when harvesting with 600 Series cutting platforms attached to pre-60 Series combines equipped with tall drive tires (for example, 35.5x32-in. or 42-in. dual wheels), it may not be possible to obtain the desired or optimum cutting bar angle. This is due to the extreme height of the drive tires, especially if used in conjunction with the tall 18.4x30 or 28Lx26 high-flotation rear steering tires.

 

The wedge kit allows the lower frame of the platform to be tilted upward to any one of three different degrees when attached to the combine so the desired cutter bar angle adjustment can be obtained.

Distance between center of F.H. and the groundDistance between center of F.H. and the ground

The following chart and illustration below can be used to help determine if the wedge kit is required on the platform for the combine being used.

 

Position machine on flat level ground with platform removed.

 

Position feederhouse so face is perpendicular to the ground. To check this, a bubble level can be placed on the face of the feederhouse.

 

Measure distance (A) between the center of feederhouse drive shaft and the ground.

 

Compare dimension to table and determine amount of wedge angle required.

 

For 50 Series STS™ Combine
Dimension A
Wedge Angle Required
Less than 710 mm (28 in.)

 

None

 

710 to 775 mm (28 to 30.5 in.)

 

1.5-degree wedge

 

775 to 825 mm (30.5 to 32.5 in.)

 

3-degree wedge

 

More than 825 mm (32.5 in.)

 

4.5-degree wedge

 

 

For 50 Series and Prior Walker Combines
Dimension A
Wedge Angle Required
Less than 710 mm (28.0 in.)

 

None

 

710 to 750 mm (28.0 to 29.5 in.)

 

1.5-degree wedge

 

750 to 790 mm (29.5 to 31.0 in.)

 

3-degree wedge

 

More than 790 mm (31.0 in.)

 

4.5-degree wedge

 

Reel Position (Fore/Aft and Height) Resume for use on all 600 Series Platforms - BH84265

Three programmable reel position settings will optimize platform performance while minimizing header losses.  The operator can preselect three different reel positions for specific field conditions and can access these while harvesting, simply by touching the activation buttons on the multifunction hydro handle.

 

Feature benefit:

  • Three programmable positions to optimize platform performance
  • Reduces operator stress by conveniently moving the reel to a preselected position to minimize header losses
Fore-aft reel resumeFore-aft reel resume
#

Functionality:

 

Adjust the reel height and fore-aft position to an optimal position then press the 1, 2, or 3 button on the multifunction control lever until arrows on each side of the symbol indicates that the system is active. This will save that reel position for that button which can be done for each number on the handle.

600D Series Draper Platforms

DRAPER HITCH EXTENSION - BH84649
Dual Float Zone Attachment - BXE10132
Combine with 625DCombine with 625D

The optional dual zone float kit provides better platform balance for a more accurate cut height right to left. The dual zone system allows the operator to independently adjust float pressure to the right and left float cylinders. Independent float cylinders adjustments allow the platform to tilt independently or in conjunction with the feederhouse.

  • Contour-Master™ feederhouse - allows platform to stay level with the tilting feeder house.
  • LevelLand feeder house - allows platform to stay level with the contours of the ground.
Feed Drum Anti-Wrap Bundle - BXE10325
Feed drum with anti-wrap brackets installedFeed drum with anti-wrap brackets installed

The feed drum anti-wrap attachment is recommended for tall, damp crop conditions to reduce drum wrapping. The attachment consists of two brackets that mount near the outer edge of the feed drum and reduce the likelihood of crop wrapping around the drum.

Feed Drum Anti-Wrap Bundle - BXE10412
Feed drum with anti-wrap brackets installedFeed drum with anti-wrap brackets installed

The feed drum anti-wrap attachment is recommended for tall, damp crop conditions to reduce drum wrapping. The attachment consists of two brackets that mount near the outer edge of the feed drum and reduce the likelihood of crop wrapping around the drum.

600D Series and 600FD HydraFlex Series Draper Platforms

Reel Flip-Over Bundle for 625, 630, 635D (Model Year 2008 or Newer) and 630FD, 635FD (Model Year 2012–2015) - BXE10262

All reels feature a low-profile pickup design to allow gentle entry into the crops to reduce shatter loss. However, in some conditions, the reel may wrap crop material, limiting the draper's capacity, and may increase losses at the reel. There is a pan design called the end shield that prevents the reel from getting into the divider point.

 

A field-installed attachment is available for the 635D, 630FD, and 635FD single poly-tine along with the 640D and 640FD two-piece poly-tine reels to reduce reel wrapping and prevent the reel from getting into the divider point.

Reel flip-overReel flip-over
Reel Flip-Over Bundle for 625D, 630D, 635D (Model Year 2017 or Newer) - BXE10873

The reel tine flip-over attachment makes it so the reel fingers point upward when completing the rotation at the top of the reel, instead of pointing to the ground.

 

John Deere value:

  • Reduces wrapping of crop material in tough, wet, viney crops such as soybeans, peas, straight cut edible beans, and canola
  • Reduces crop wrapping and increases the draper’s capacity, which reduces losses at the reel
  • Increases visibility to the front of the draper
Reel flip-over attachmentReel flip-over attachment
Reel Flip-Over Bundle for 630FD and 635FD (Model Year 2016 or newer) - BXE10760

All reels feature a low-profile pickup design to allow gentle entry into the crops to reduce shatter loss. However, in some conditions, the reel may wrap crop material, limiting the draper's capacity, and may increase losses at the reel. There is a pan design called the end shield that prevents the reel from getting into the divider point.

 

A field-installed attachment is available for the 635D, 630FD, and 635FD single poly-tine along with the 640D and 640FD two-piece poly-tine reels to reduce reel wrapping and prevent the reel from getting into the divider point.

Reel flip-overReel flip-over